Home › Brick Veneer Installation
Legendary Masonry Lubbock offers precise installation of brick veneers in Lubbock, TX for siding, accent walls, and facades. Thin brick systems give you the classic brick look without full thickness walls. We handle moisture control, proper anchoring, and detailed patterns so your brick veneer looks authentic and lasts.
Legendary Masonry Lubbock provides professional brick veneers throughout Lubbock, TX, Texas and the surrounding area. Our licensed, insured crew delivers safe, clean, on-time work with a free estimate before anything begins. Call 806-425-5011 or request your free quote.
Brick veneers that fit Lubbock homes and weather
Brick veneers give you the look of solid brick without rebuilding your whole wall, but they still have to stand up to West Texas wind, dust, and temperature swings. At Legendary Masonry Lubbock, we install brick veneers specifically with Lubbock conditions in mind, so you get curb appeal that does not start cracking or separating in a few seasons.
A brick veneer is a non structural brick face that sits in front of a wood, metal, or block wall. The key to a good install is how that thin brick layer is attached, how water is managed behind it, and how it handles our hot, dry summers with the occasional pounding rain and freeze. On this page we explain exactly how we install brick veneers, what options you have, what affects cost, and what to look out for before you hire anyone to work on your house or building in Lubbock.
How we install brick veneers step by step
Every brick veneer installation from Legendary Masonry Lubbock starts with a site visit and measurement. We look at your existing wall type (wood framing, metal framing, CMU block, or concrete), check for movement or damage, and note exposure to sun and wind. West facing walls in Lubbock take a beating, so we often recommend slightly different materials or joint treatments there than on a shaded north wall.
After planning and layout, we prepare the wall. For framed walls this usually means installing exterior sheathing if it is not already there, then a proper moisture barrier or house wrap rated for our wind loads. Over that we install metal lath or a brick veneer panel system, depending on whether we are doing a traditional mortar set veneer or a mechanically fastened system. For block or concrete, we clean the surface, repair cracks, and use bond enhancers where needed to help mortar grab in our dry climate.
Next we install weep screeds and flashing at the bottom of the veneer where water can escape. In Lubbock, dust can clog poorly installed weep holes, so we size and space them so they stay functional even with wind blown dirt. Around windows and doors we use head flashing and end dams so wind driven rain from summer storms cannot work in behind the veneer.
Only after the wall is correctly prepped do we set the brick veneers. We plan bond pattern and cuts so the eye is drawn to windows and entries, not to awkward slivers at corners. Our masons lay the thin bricks or full face bricks in fresh mortar, keep consistent spacing, and tool joints to the profile you choose. For tall walls or commercial façades we use mechanical anchors at engineered intervals so the veneer is locked to the structure, not just held by mortar.
We finish by cleaning the brick faces with products that will not bleach or streak the clay in our strong sun. Then we seal or leave natural, based on the brick type and your preference. Before we call it done, we walk the project with you and point out expansion joints, weeps, and other details so you know how the system works and what to watch over time.
Design, material, and layout choices for your veneer
Lubbock homes and businesses range from older brick ranch houses to newer stucco and siding builds, so brick veneer design is not one size fits all. Legendary Masonry Lubbock helps you choose brick veneers that match or upgrade your style instead of fighting it.
Brick type is your first big decision. We install thin brick veneer (about half to three quarter inch thick) for interior walls, fireplace faces, and some exterior retrofits where weight is a concern. For heavier duty work we use full face brick veneer, usually around 3 inches thick, that sits on a ledge or angle iron and gives the look of a full brick wall. In Lubbock, darker reds and earth tones tend to hide dust better, which matters if you are near fields or unpaved roads.
Texture and finish also change how the wall reads. Smooth face veneers look cleaner and more modern, while tumbled or wire cut textures hide minor dirt and chips. On commercial storefronts we often combine a clean running bond at eye level with a more textured soldier course or rowlock at the base to break up the façade and handle scuffs from foot traffic.
Pattern is another tool we use. A standard running bond works for most houses, but older Lubbock neighborhoods sometimes call for matching an existing pattern or joint style so an addition does not look patched on. We can tie new brick veneers visually into original brick by adjusting mortar color, joint width, and layout. For accent walls, we might use herringbone or basketweave inside, where weather is not an issue and you can afford a bit more design.
Mortar color is not just cosmetic in our sun. A bright white joint will reflect more light and can make a wall look washed out under a clear West Texas sky. Off white, buff, or light gray joints usually give a steadier look all day. During planning, we show you real samples outside at different times of day so you see what your veneer will look like, not just a small chip under fluorescent lights.
What affects cost and how we control problems on Lubbock projects
Brick veneer pricing is driven more by labor and prep than by the brick itself. When Legendary Masonry Lubbock quotes a job, we break down what you are paying for so there are fewer surprises. Square footage is a big driver, but two walls with the same area can cost very different amounts depending on access, height, and cut work.
Preparation is usually the largest variable. If your existing wall is flat, dry, and sound, we can keep prep simple. If we discover moisture damage, framing issues, or out of plumb walls, we will address that before hanging any veneer so you are not covering up a problem that will crack your new brick later. In older Lubbock homes, we see a lot of past DIY work, especially around porch enclosures and garage conversions, so we plan extra time to straighten and reinforce those areas.
Openings and details also affect cost. Lots of windows, doors, bay projections, and archways means more cuts and more layout time. Tall walls that need staging, or projects that require night or weekend work around a business schedule, add labor. Materials like upgraded moisture barriers, stainless anchors, or specialty mortars cost more upfront but make sense on heavily exposed walls or commercial jobs where failure is not an option.
Common brick veneer problems in our area include hairline cracking at corners from building movement, bulging sections where anchors or ties were skipped, and efflorescence (white mineral deposits) from improper drainage. We design around these: adding control joints where the structure is likely to move, installing ties to meet or exceed code, and detailing weeps and flashing so water has an easy path out.
During installation, we watch weather closely. Very hot, dry, and windy days can cause mortar to cure too fast, which weakens the bond. On those days we adjust work hours, shade the wall where practical, and modify our mix and curing steps so the mortar gains strength instead of turning chalky. These are the small local decisions that keep a good looking veneer from becoming a maintenance headache.
What Lubbock property owners should know before hiring
Before you hire anyone for brick veneers in Lubbock, ask how they handle moisture, movement, and wind load. If the answer is mostly about color charts and style photos, keep looking. The veneer is only as good as the hidden work behind it. At Legendary Masonry Lubbock, we are happy to explain exactly what water barrier we are using, how many ties per square foot, and where control joints will go, and we will put that scope in writing.
Check that your contractor understands local codes and typical Lubbock construction. Many of our homes have slab foundations with some settling, and we see a mix of older solid brick homes and newer framed walls with various sidings. Each wall type needs the right attachment system and sometimes engineered support angles, especially over garage doors and wide windows. If a bid looks much cheaper than the rest, it often means they are skipping structural steel angles or quality flashing.
You should also know what you want from the project. For a house you plan to keep long term, it makes sense to invest in better underlayment, venting, and brick quality so the veneer looks right for decades. For a rental or a quick resale, you might focus more on visible impact on the front elevation and keep side and back walls simpler. We will walk you through options that match your timeline and budget.
Finally, ask to see past work in Lubbock, not just stock photos. We can usually point you to homes and businesses where you can drive by and see how our brick veneers have held up to several summers and dust storms. That real world evidence is hard to fake. When you are ready, we can schedule a visit, look at your walls, talk through design ideas, and provide a clear, detailed proposal so you know exactly what your brick veneer installation will involve.
